If the display on the heater shows “ER” when connected to electricity, this may indicate that the electronic tilt switch is activated. Please follow these steps to disable the tilt switch:

1. Ensure the heater is positioned with the LCD facing upwards or angled up to 90° to the right or left. It should not be facing downwards.
2. While turning on the power to the unit or plugging it into an outlet, press “T-” followed immediately by “T+”. The display should then show “OF” or “ON”—where “OF” means the tip protection is deactivated, and “ON” means it is activated.
3. Select “OF” to disable the electronic tilt switch.

With the tilt switch disabled, the heater can function in any orientation and may be mounted on a wall or ceiling.

Note: The heater cannot be placed on a stand when the tilt switch is disabled, for safety reasons.

The heater will now work in any mounting direction and can only be mounted on the wall or ceiling.

NOTE! The heater can not be amounted on a stand when the tilt switch is disabled due to safety reasons.

Opranic products are sold through wholesalers, retail stores, and e-retailers. In each country, our aim is to have a distributor that distributes the products locally to the retailers and wholesalers. Therefore we do not list the retailer’s shops on opranic.com. You can find each distributor under our distribution section and go to their website for an updated reseller list.

Starting from mid-September 2017, we also sell our products directly on our web shop https://www.shop.opranic.com.

Yes, as long as you follow the safety distances mentioned in the user manual that came with the heater. It is also available on our media bank.

The length of the cable is 2,0 meter (some models that are produced before Maj, 2017 can be 1,6 meter long) with a European plug (type F).

When purchase the box contains Heater, Manual, Screws, 4 units of mounting brackets and a remote control for the “R” versions. If you are lacking any items in your box, please contact us and we will send out the missing part directly.

For wall or ceiling mounting the height distance to the floor has to be minimum 1.8 meters, according to CE regulations. A recommended installation height, an example for a terrace is 1.8-2.3 meters for powers up to 2300W. VEGA series requires higher installation heights from 4 meters and above.

Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. However, if you need to use an extension cord the cord shall be 2mm (14 AWG) minimum size and rated not less than 16A.

Yes, the remote control is the same for all Opranic remote controlled heaters. If you purchase two heaters, you can use the same remote control for both heaters. Just point the remote towards the heater (max distance 8-10 meters) and select the desired power.

No, the thermostatically controlled models do not have power levels. It has a temperature sensor inside the heater that switches on and off depending on the temperature of the heater body. You can adjust the thermostat, so it switches off/on several of times per hour or having it on max for continuous on.

Theoretically, you will always have the same level of radiation heat on your skin no matter of the surrounding temperature. However, the cooling effect due to low temperatures and air movements cools the skin and to compensate that you need to supply more energy (heat).

Opranic heaters convert 96% of the energy to radiation heat, so Opranic heaters are very efficient, the highest wind resistance of any outdoor heaters on the market due to the unique technology of radiation that also has a very high absorption level for human skin.

For an isolated indoor room, a 2300W heater is well enough to heat 23 square meters. However, for an outdoor environment when you have no isolation and the energy is consumed by the constant air movements, a 2300W heater covers approximately a 13 square meter area.

Please see our heat coverage images and guides in the sidebar to the right.

If you need any further assistance, please feel free to contact us!

We have a stand for our ECO Series.

The other models are for Wall or Ceiling mounting.

The Opranic heaters produced to be able to withstand rust and oxidation. Strong direct sunshine, snow and other weather conditions degrade any materials over time, so to keep your heater in good condition we recommend to have it either installed under a ceiling or cover it during a longer period of not use.

The body is constructed of aluminium and can stand and will have very little degradation from outdoor use.

The front grid is made of chromed steel and can have some tendencies to react to an outdoor climate. However, if you are experiencing any degrade of the front grid, it is possible to exchange the grid. Please contact us and we will assist you with a spare front grid.

The side covers are produced with a special glass fibre plastic that has a very high level of protection against any climate degradation. But if you accidentally have dropped the heater and the plastic is broken, just contact us and we can assist you with a new side cover.

The Opranic heaters has a 2 year warranty.

If your remote controlled heater does do respond either on remote signals or the buttons on the heater. Please then try a reset. The reset is performed as follow;

Recommended to be two persons for this reset procedure.

1. Unplug the heater from the electrical outlet
2. Press and hold both two buttons (true step 2-4) on the heater push in
3. Attach the power to the power outlet
4. .In about 5 seconds you will hear a sound “pip”.
5. Then release the buttons.

You have now performed a reset, and hopefully, your heater is functioning again.

If not, please contact us and we will assist you.